DIN EN 13414-1/A1-2005 钢丝绳吊索.安全.第1部分:通用提升设备用吊索

作者:标准资料网时间:2024-05-13 15:48:59 浏览:8484 来源:标准资料网

【英文标准名称】:Steelwireropeslings-Safety-Part1:Slingsforgeneralliftingservice;GermanversionEN13414-1:2003/A1:2005
【原文标准名称】:钢丝绳吊索.安全.第1部分:通用提升设备用吊索
【标准号】:DINEN13414-1/A1-2005
【标准状态】:作废
【国别】:德国
【发布日期】:2005-09-01
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:起重吊索;荷载能力;安全;安全要求;钢丝;绳索;金属丝吊索;接线端配件(绳索);金属丝绳;提升设备;检验;钢丝绳;设备安全;危害;定义;试验;尺寸;规范(验收);安全工程
【英文主题词】:Definition;Definitions;Dimensions;Equipmentsafety;Hazards;Hoistingslings;Inspection;Liftingequipment;Loadcapacity;Ropes;Safety;Safetyengineering;Safetyrequirements;Specification(approval);Steelwires;Steel-wireropes;Terminalfittings(ropes);Testing;Wireropeslings;Wireropes
【摘要】:ThisEuropeanStandardspecifiestheconstructionrequirements,methodsofrating,testingandcertificationofwireropeslings.Itcoverssingle-,two-,three-,four-leggedandendlesswireropeslings,madefrom:6-and8-strandordinarylaysteelwireropefrom8mmto60mmdiameterwithferrulesecuredeyeterminationsorsplicedeyeterminations.Thehazardscoveredbythisstandardareidentifiedinclause4.GuidanceontheinformationtobeprovidedwithanenquiryororderisgiveninannexA.
【中国标准分类号】:H49
【国际标准分类号】:53_020_30
【页数】:7P;A4
【正文语种】:德语

下载地址: 点击此处下载

返回跳至顶部

上一篇: BS EN 10324-2005 钢丝和钢丝制品.软管加筋钢丝
下一篇: DIN EN 13414-2/A1-2005 钢丝绳吊索.安全.第2部分:生产商提供的使用和维护信息规范；德文版本EN13414-2-2003/A1-2005

基本信息

标准名称：	机床夹具零件及部件螺钉用垫板
英文名称：	The parts and units of jigs and fixtures - Screw gasket
中标分类：	机械 >> 工艺装备 >> 一般卡具
ICS分类：	综合、术语学、标准化、文献 >> 词汇 >> 电气工程 (词汇)
替代情况：	JB/T 8042-1995(原标准号GB/T 2255-1991)
发布部门：	机械科学研究院
发布日期：	1999-08-06
实施日期：	2000-01-01
首发日期：	1900-01-01
作废日期：	1900-01-01
归口单位：	机械科学研究院
出版日期：	1900-01-01
页数：	2 页
批文号：	国机管[1999]433号

适用范围

JB/T 8042-1999 本标准是对 JB/T 8042-95《机床夹具零件及部件螺钉用垫板》的修订，修订时仅按有关规定作了编辑性修改，技术内容没有改变。本标准规定了规格为 5.5～19mm 的螺钉用垫板。本标准于 1981 年以 GB 2255-80 首次发布，于 1991年 4 月 30 日第一次修订为 GB/T 2255-91，于 1996 年 4 调整为 JB/T 8042-95。

前言

没有内容

引用标准

没有内容

所属分类：机械工艺装备一般卡具综合术语学标准化文献词汇电气工程 (词汇)

Product Code:SAE J2950
Title:Recommended Practices (RP) for Transportation and Handling of Automotive-type Rechargeable Energy Storage Systems (RESS).
Issuing Committee:Battery Transportation Committee
Scope: This RP covers the recommended practices associated with identification, handling, and shipping of un-installed RESSs to/from specified locations (types) required for the appropriate disposition of new and used items. For the purposes of subject RP, the generic term “RESS” shall be used to identify automotive-type and sized “traction” and Start, Light and Ignition (SLI) batteries when used as intended by the vehicle and RESS original equipment manufacturers (OEMs) for ground vehicles. It is the specific intent of the authors to fully utilize and reference existing US laws, regulations, published policies, and existing industry practices to the maximum extent possible; and to provide design and performance recommendations only to those areas for which none of the previous documents exist.
Rationale: This RP covers the recommended practices associated with identification, handling, and shipping of un-installed RESSs to/from specified locations (types) required for the appropriate disposition of new and used items. For the purposes of subject RP, the generic term “RESS” shall be used to identify automotive-type and sized “traction” and Start, Light and Ignition (SLI) batteries when used as intended by the vehicle and RESS original equipment manufacturers (OEMs) for ground vehicles. It is the specific intent of the authors to fully utilize and reference existing US laws, regulations, published policies, and existing industry practices to the maximum extent possible; and to provide design and performance recommendations only to those areas for which none of the previous documents exist.