EN 869-2006 机械安全.金属压力铸造设备安全要求

作者:标准资料网时间:2024-05-16 16:20:42 浏览:9317 来源:标准资料网

【英文标准名称】:Safetyofmachinery-Safetyrequirementsforpressuremetaldiecastingunits;EnglishversionofDINEN869:2007-02
【原文标准名称】:机械安全.金属压力铸造设备安全要求
【标准号】:EN869-2006
【标准状态】:现行
【国别】:
【发布日期】:2007-02
【实施或试行日期】:2007-02-01
【发布单位】:欧洲标准学会(EN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:铸造金属;交付使用;缺陷与故障;缺陷;定义;压铸机;压铸冲摸法;压铸;文献工作;铸造设备;危害;维修;手册;作标记;机械工程;职业安全;保护设备;保护措施;安全;安全措施;安全要求;规范(验收);用户信息
【英文主题词】:Castmetals;Commissioning;Defects;Definition;Definitions;Diecastingmachines;Diecastingmethods;Diecasting;Documentations;Foundryequipment;Hazards;Maintenance;Manuals;Marking;Mechanicalengineering;Occupationalsafety;Protectiondevices;Protectivemeasures;Safety;Safetymeasures;Safetyrequirements;Specification(approval);Userinformation
【摘要】:
【中国标准分类号】:J61
【国际标准分类号】:25_120_30
【页数】:44P.;A4
【正文语种】:英语

下载地址: 点击此处下载

返回跳至顶部

上一篇: EN 10130-2006 冷成形用冷轧低碳钢平板产品.技术交货条件
下一篇: EN 15024-2-2006 铜和铜合金.锌含量的测定.第2部分:火焰原子吸收光谱法(FAAS)

【英文标准名称】:Nominalranges,scalespacingandscalenumberingofaccuracyclasses0,2,0,3and0,6pressuregauges
【原文标准名称】:精确度级别为0.2.0.3和0.6的过压测量仪表的指示范围.刻度顺序和标注数字
【标准号】:DIN16123-1987
【标准状态】:作废
【国别】:德国
【发布日期】:1987-02
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:作标记;精密度;测量仪器;数字;压力测量(流体);仪表刻度;刻度盘;压力过载;压力计;仪表;划刻度
【英文主题词】:dials;measuringinstruments;pressuremeasurement(fluids);instrumentscales;pressuregauges;digits;pressureoverload;graduations;precision;marking;meters
【摘要】:
【中国标准分类号】:N06
【国际标准分类号】:17_100
【页数】:4P;A4
【正文语种】:德语

Product Code:SAE J2180
Title:A Tilt Table Procedure for Measuring the Static Rollover Threshold for Heavy Trucks
Issuing Committee:Truck And Bus Total Vehicle Steering Committee
Scope:The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.The purpose of this SAE Recommended Practice is to provide an interim test procedure for using tilt tables to measure a static rollover threshold for heavy trucks.